Whole-Home Repiping for Utah Homes
Serving the Wasatch Front and Beyond
Before we recommend a full repipe, we inspect your home's plumbing to understand what is actually happening. If spot repairs will hold, we will tell you honestly. When a repipe is the right call, we provide a written quote that names the material, pull the required permit, and open only what we have to. The work follows a written timeline. And the price is flat-rate and in writing before anything starts.
Get Your Repipe Estimate
Quick answer
Yes, Blue Best repipes homes across Utah, serving the Wasatch Front and beyond. We inspect your plumbing first and give an honest answer on whether spot repairs will hold. You receive a written quote naming the pipe material, PEX or copper. Utah's plumbing code requires a permit for replacement piping, a rough-in inspection before walls close, and new piping tested tight. We provide a written timeline and a flat-rate price in writing first.
How can you tell your home needs a repipe?
Rusty water first thing
When you turn on a faucet after the water has sat overnight, the first flow comes out rusty or brown. We check for this sign during our inspection.
Pressure fades with two taps
You notice the shower pressure drops sharply when someone flushes a toilet or starts the kitchen sink. We test your system to find the cause.
A third leak this year
You have already repaired two leaks in the past twelve months, and now a third pipe has failed. We can tell you whether spot repairs will hold.
Polybutylene pipe in the basement
We identify this material during our visit.
Galvanized pipe under the sink
The pipe connected to your sink faucet is a dull silver metal that a magnet sticks to. We check for this type of pipe throughout the house.
Green stains at copper joints
A blue-green crust has formed on the copper fittings under your sinks or near the water heater. We inspect these joints for pinhole leaks.
A remodel that opens the walls
You are planning a renovation that will expose the interior of your walls anyway. We can repipe while the framing is accessible.
Home bought without a plumbing inspection
You purchased the house without having a plumber look at the pipes first. We inspect the existing system to give you an honest answer.
A repipe quote to check
You have received a quote from another contractor for a full repipe. We offer a free second opinion on any competitor's repipe quote.
Why do Wasatch Front homes need repiping?
Scale from hard water narrows old galvanized pipe. Rust-colored water comes from galvanized lines. The polybutylene standard was withdrawn in 2010 with no replacement standard. Polybutylene is absent from Utah's pipe tables. Galvanized steel remains a listed material. Lead is more likely in homes built before 1986. The code allows 80 psi static maximum.
Approved materials
Inside the house, code allows CPVC, copper types K, L, and M, PEX, and galvanized steel. From the meter to the house, polyethylene and PVC rated at least 160 psi are also listed. Polybutylene appears in neither table, and its standard was withdrawn in 2010.[1]
PEX explained
PEX standards first published in 1984 entered a national model code in 1993. The plastics pipe institute reports a minimum extrapolated lifetime of 50 years under a hot chlorinated-water test. Frozen PEX usually expands without cracking. Code allows flared, mechanical, or push-fit joints with hangers every 32 inches for pipe 1 inch and smaller.[2]
Copper details
Copper keeps a smooth bore with no corrosion allowance in design. Type M is recommended for distribution. A dielectric fitting connects copper to galvanized. Lead-free solder and flux are required.[3]
Permits and inspections
Replacing concealed pipe requires a permit. Inspections cover underground, rough-in, and final stages. Nothing may be covered before approval. Pipe is tested tight at working pressure or 50 psi of air. Utah law requires a licensed plumber for repiping. Ogden requires a permit to repair any plumbing system.[4]
[1] Plastics Pipe Institute - TR-56, PEX history and adoption. [2] Copper Development Association - copper tube handbook. [3] Utah Plumbing Code 2021, Chapter 6 - water supply and distribution. [4] Utah Code Title 58, Chapter 55 - construction trades licensing. [5] Full source list: data-sources
We inspect first and give an honest answer on whether spot repairs will hold. You receive a written quote naming the pipe material, PEX or copper. We open only what we have to. We offer a free second opinion on any competitor's repipe quote. Sometimes the other quote is right.
Which repipe approach fits your home?
Every home is different, so here is how the three options compare.
PEX repipe
- ✓Best for: Homes needing flexible routing.
- ✓PEX is flexible, uses long lengths and home-run layouts; the plastics pipe institute reports a 50-year extrapolated minimum under test; joints are flared, mechanical, or push-fit.
Copper repipe
- ✓Best for: Homes wanting rigid metal piping.
- ✓Copper has a smooth bore with no corrosion allowance; code requires lead-free solder and dielectric fittings at galvanized connections.
Partial repipe
- ✓Best for: A single failing run.
- ✓One failing run is replaced; code still requires a permit and inspection.
What you get with a Blue Best repipe
Inspection first
We inspect your home before any work begins and give an honest answer on whether spot repairs will hold.
Written quote and timeline
You receive a written quote naming the pipe material, PEX or copper and a written timeline for the scheduled work.
Permit and cleanup
We pull the permit and open only what we have to, with paperwork in hand at the end.
Recognition & accreditation
Financing available on qualifying installations, subject to credit approval; ask when you call.
Locally and women-owned and operated meet the owners Google Business Profile.
What our repipe includes
Flat-rate price
You get a flat-rate price in writing before work begins, with no surprise at the end.
Licensed plumbers
Our W-2 employees are licensed plumbers, and we use no subcontractors.
Permit pulled
A permit is pulled on every repipe, and change orders need your approval.
Hard-water sizing
Fixtures and lines are sized for hard water, and softening is offered where it pays.
Workmanship guarantee
Your repipe comes with a workmanship guarantee.
Free second opinion
We offer a free second opinion on any competitor's repipe quote.
What happens after you ask for a repipe estimate?
Step 1
We respond.
We answer your call or online form.
Step 2
We inspect first.
We look at your pipes, identify the material, and check that static pressure stays under 80 psi per Utah's plumbing code. We give an honest answer on whether a spot repair will hold or a repipe is needed.
Step 3
You get a written quote.
The quote names the material, includes a written timeline, and shows a flat price for the whole job. You approve it before any work begins.
Step 4
We do the work.
We pull a permit and open only what we have to. Utah's plumbing code requires a rough-in inspection before walls close, and the system is tested tight.
Step 5
You get the finish.
A final inspection passes per Utah's plumbing code. We check pressure and connections, clean the area, and hand you the permit and paperwork.
Is your repipe quote worth a second look?
We offer a free second opinion on any repipe quote from another company. We inspect first to see what your home actually needs. Sometimes one run is enough, and a full repipe is not required. We give you a written quote to compare against the one you already have. Sometimes the other quote is right, and we will tell you that honestly.
What does a proper repipe deliver for you?
New piping tested tight
Utah's plumbing code requires new piping to hold tight at working pressure or 50 psi of air. Blue Best checks pressure and connections again at the end of every repipe.
Pressure-reducing valve
Utah's plumbing code calls for a pressure-reducing valve above 80 psi static, built to fail open. Blue Best writes it into the quote wherever the code requires it.
Shutoff valves at each fixture
Utah's plumbing code requires shutoff valves at each fixture and full-open valves at the service entrance and each dwelling. Blue Best checks all connections at the end.
Hot water runs limited
Utah's plumbing code limits hot water runs to no longer than 50 feet, with recirculation counting as the source. Blue Best sizes lines for hard water.
Inspections at every stage
Utah's plumbing code requires inspections underground, rough-in, and final, with nothing covered before approval. Blue Best hands you the permit and paperwork at the end.
Sized for your water
Blue Best sizes fixtures and lines for hard water and offers softening where it pays. Every repipe carries a workmanship guarantee.
What piping problems does a repipe solve?
Galvanized pipe
Galvanized pipe is still a listed material in Utah's plumbing code. Over time, scale builds up inside and narrows the pipe. When copper connects to galvanized, a dielectric fitting is needed. We replace failing galvanized lines with PEX or copper.
Polybutylene
The ASTM standard for polybutylene was withdrawn in 2010. This pipe is not in Utah's plumbing code tables. We replace polybutylene with PEX or copper.
Pinholes in copper
We see repeated pinhole leaks on one copper run. Utah's plumbing code sets 80 psi as the static maximum. We inspect first and give an honest answer on whether a spot repair or a full repipe will hold.
Metal service used for grounding
A metallic service pipe is used for grounding. It cannot be replaced with plastic until other approved grounding is provided. We inspect for grounding first.
Pipes in outside walls
Pipes in outside walls or attics must be protected from freezing. This means insulation, heat, or both. We check the route before we start.
Low pressure everywhere
Utah's plumbing code requires a minimum flow pressure of 8 psi at most fixtures. A booster is allowed where street pressure cannot meet it. We inspect before quoting.
What drives the cost of a repipe in Utah?
We price every repipe by the job, not by the hour. We inspect first and put the price in writing before work starts. The drivers that set that price are published upfront, so there is no surprise at the end. When spot repairs will hold, we say so honestly. Blue Best quotes an exact price in writing before any work begins.
The price depends on the material, access and how much wall is opened, fixture count, drywall to restore, and the permit. We also offer a free second opinion on any competitor's repipe quote.
Quoted free
Inspection and quote - We inspect first and give a written price before any work.
Quoted upfront
Partial repipe - Replacing one run of pipe instead of the whole house.
Quoted upfront
Whole-home PEX - A full repipe using flexible PEX tubing.
Quoted upfront
Whole-home copper - A full repipe using rigid copper pipe.
Quoted upfront
Valves and tank - A pressure-reducing valve, expansion tank, or new shutoff valves.
What does Blue Best guarantee in writing?
On new equipment installs
a 1-year labor warranty - extendable for customers on a Blue Best Maintenance Plan - the parts warranty (typically 10 years on qualifying Lennox and Amana equipment) registered for you, and no-lemon coverage on major components like compressors and heat exchangers.
On any quoted work
the price you sign is the price you pay - change orders require your approval before we do the work. Plus a free second opinion on any competitor's replacement quote (no blanket price-match - sometimes our honest answer is "take their deal").
What we won't promise
real-world comfort depends on duct condition, insulation, and infiltration, so we disclose those dependencies rather than guarantee a number. The 5.0 rating from 2,900+ reviews is the audit trail.
Common Questions About Repiping
Repeated leaks on the same run are a clear sign your plumbing is failing. Rust-colored water coming from galvanized lines also indicates deterioration. We inspect first to give you an honest answer on whether spot repairs will hold or a full repipe is needed. Polybutylene is not an approved material under Utah's plumbing code.
It carries a 50-year minimum extrapolated lifetime under a hot chlorinated-water test. Frozen PEX usually expands without cracking. Utah's code allows flared, mechanical, or push-fit joints, and requires hangers every 32 inches for small PEX.
Utah's code requires an underground inspection, a rough-in inspection before walls or ceilings close, and a final inspection. Nothing can be covered before approval. We make sure your permit and paperwork are in hand when the job is complete.
We open only what we have to. Utah's code requires that finished surfaces changed during plumbing work be left in a safe structural condition, and that framing not be cut or notched beyond limits. Any change orders need your approval.
Yes, and we offer a free second opinion on any competitor's repipe quote. We give an honest answer on whether spot repairs will hold. Sometimes one run is enough, and sometimes the other quote is right.
Inside the house, Utah's plumbing code lists CPVC, copper, PEX, and galvanized steel as approved materials. For the service line, polyethylene and PVC are also listed.Polybutylene is absent from the approved list.
You receive a written quote naming the pipe material, PEX or copper, and we pull a permit. New supply lines are installed in PEX or copper. Utah's code requires shutoff valves at each fixture, rough-in and final inspections, and a pressure test to confirm tightness. We check pressure and connections at the end and clean the area.
Utah's code does not allow replacing a metal service line used for grounding with plastic until other approved grounding is provided. We inspect for this condition first.
Yes. Utah's code requires a pressure-reducing valve above 80 psi static, an expansion device where a reducing valve isolates the heater, and a water-hammer arrestor with quick-closing valves. Where the code requires them, these items are written into your quote.
Terms in plain English
Repipe
Replacing the water supply piping inside a house, either the whole house or one run.
PEX
Flexible plastic tubing that uses flared, mechanical, or push-fit joints.
Galvanized steel
Zinc-coated steel pipe that is still listed in Utah's plumbing code; scale buildup narrows it over time.
Polybutylene
A plastic supply pipe whose standard was withdrawn in 2010 and is not in Utah's plumbing tables.
Dielectric fitting
A fitting that joins copper to galvanized steel and separates the two metals.
Rough-in inspection
An inspection where piping is checked before the walls close.
Pressure-reducing valve
A valve required when static pressure is above 80 psi; it is built to fail open.
Pressure test
A test at working pressure or 50 psi of air to see if the system is tight or not.
What homeowners say
Elizabeth M
1 week ago
Our experience with Blue Best has been fantastic. Shawn, Carson and Khaing have done any amazing job with fixing our shower and pressure valve, patching the drywall, and installing both a water...
Aaron
2 weeks ago
I have been using these people for three years. Costumer service is outstanding and they were able to give me advice on my issue until they came out in a few weeks. Would recommend, but make sure to...
Marian Young
3 weeks ago
We used Blue Best for many projects in our home (faucet replacement, HVAC, installing manifold, replace steam system, etc). Shawn was knowladgable, courteous, explained everything and cleaned up the...
Jeffery Hansen
1 month ago
Just had Roger Pay, our technician complete sumner service on our new (Heat Pump System). He was courteous and thorough but most important, professional. We had BLUE BEST put in a new heat pump in...
